heavy duty wheel chocks

Why and How I Repositioned Our 2020 Scamp’s Shower Pump

https://scampgrounds.com/wp-content/themes/osmosis/images/empty/thumbnail.jpg 150 150 gavin gavin https://secure.gravatar.com/avatar/9de79417d52cde759ffedf503509748a?s=96&d=mm&r=g October 18, 2022 October 6, 2022

Why and How I Repositioned Our 2020 Scamp’s Shower Pump

In the past two years since taking delivery of our 2020 Scamp 13’, I haven’t spent much time looking underneath the camper.  I did add underglow lighting and had to replace a faulty Grey tank capacity sensor over the past couple of years, but other than these things most of my attention has been above the floor.  It was only this past month, when we ran into trouble south of the Trona Pinnacles, did I see how exposed and perilous a position where the factory installed shower pump sits.  On this misadventure, after a series of unfortunate events (lack of signs, wrong turns, continually narrowing roads), we found ourselves on a grueling ATV trail with no easy and safe way to turn around.  Here’s a short video from our off road drive!  When we finally arrived at the Pinnacles from the south, we noticed our shower water pump (which hangs down really low below the Scamp) was damaged.  One of the hose connectors on the pump was completely broken off and the vinyl tubing was dangling down to the ground.  Fortunately, an RV repair shop about an hour away was able to replace our pump immediately so we could continue on with our trip.  The mechanic and I spoke about repositioning the pump into a nice protected recessed area (under where the toilet sits) adjacent to the factory position, but due to concern about the tubing becoming pinched, and our time constraints, we opted to leave it in its original spot.

When we returned home, I resolved to reposition the shower pump into the protected recessed position (under where the toilet sits) to avoid a potential repeat of what happened south of the Trona Pinnacles.  The first thing I did was call Scamp and ask why the shower pump is factory mounted in the low center exposed position (under the shower pan).  I was told that it is placed in this position because the plumbing hoses will get pinched or crimped if it is put in the deeper recessed position.  This is exactly what the mechanic told me when trying to replace the new pump in this location.  There really isn’t much room for the vinyl tubing to attach to the hose adapters on the pump and make such a sharp turn in the small recessed area to avoid the trailer frame.  Ultimately, after some research, I decided to use 90 degree threaded elbow connectors to address this problem.  The hardest part of the project was figuring out all the supplies and tools I needed.  After that, the actual relocation of the Scamp shower pump was relatively easy and only took about an hour working slowly and cautiously.  Here are the Project Tools and Supplies I used to relocate the Scamp 13’ shower pump.

Project Tools and Supplies:

a.  Tools

1. 1. Square #2 Screwdriver or
      1. Electric screw driver which accepts ¼” bits
      2. Square #2 bits
   2. Pex / Vinyl Tubing Cutter
   3. Metal Snips
   4. Wire cutters
   5. Crimper tool

 b.  Supplies

1. 1. ¾” ID, 1” OD vinyl tubing w/clamps (10 feet) 
   2. Two ½” PVC 90-Degree MPT x FPT Elbow Fitting (threaded inside and out)
   3. Wire similar in thickness to existing pump wire to extend wire for reposition, butt connectors

Here are the Project Steps I took to relocate the Scamp 13’ shower pump.

Project Steps:

1. SAFETY: I made sure my Scamp 13’ was parked on a flat level surface (my garage), the tongue jack was stable, and I used heavy duty wheel chocks to prevent the trailer from rolling.  I also wore safety glasses to help prevent anything from falling into my eyes while working under the trailer.  I also made sure my mobile phone was within reach in case I needed to call for help when working.
2. Using the Square #2 Driver, I removed the two square #2 screws which hold the metal strap around the shower pump
3. I unscrewed the metal hose clamps on the pump’s inlet and outlet (and placed little plastic containers under the hoses to prevent grey water from dripping onto the garage floor) and pulled both hoses from the pump’s inlet and outlet.
4. I removed the shower pump by unscrewing the four Phillips head screws holding the pump’s rubber feet to the Scamp’s under floor (I left the 4 screws in the rubber feet to use again when remounting) and set the pump on the garage floor
5. I would have cut and extended the black and red wires at this time (using new wire, wire cutters, butt connectors, etc.) to allow repositioning to the farther recessed area, but the mechanic who installed the new pump already extended the wires for me (before deciding he couldn’t easily reposition the pump)
6. I removed the black plastic hose adapters from the pump inlet / outlet by manually unscrewing them from the pump
7. I set the white ½” plastic threaded elbow connectors and black hose adapters down next to the pump on the floor facing toward the rear of the Scamp 13’ to visualize the setup
8. I screwed on the white PVC ½” elbow connectors directly onto the pump. I found that I could only screw them on about 4 full turns and didn’t force turning them any more to prevent possible cracking.  I made sure their final position was facing back toward the rear of the Scamp (the rear of the pump has the big square and the front is the cylinder with aerodynamic small bulb).  Then, I screwed on the black hose adapters onto the white elbow connectors so they faced straight back.
9. I positioned the pump into the protected recessed area under the toilet (as far forward as possible without the elbows hitting the metal frame) and, using the existing screws, I mounted the pump (the screws self-tap into the floor) (I was told the Scamp floor is ¾” thick and verified the thickness by measuring the exposed floor thickness next to the shower drain under the trailer, but I used the existing screws since they were in good condition so didn’t need to be concerned with screw length).
10. I remounted the metal strap using the existing square #2 screws around the pump to secure it (using my metal snips, I clipped off one small segment / one hole so the strap would fit into the small area).
11. Lastly, I attached the hoses using the metal clamps (from filter outlet to pump inlet, from pump outlet to Grey tank). The Tube Cutter made the job very easy; cutting the thick vinyl is just a quick snip.
    1. I put the metal clamps on the vinyl tube ends first before pushing them over the inlets/outlets.
    2. Grey Tank hose to Pump outlet: I was really careful not to cut the Grey tank hose too short (since that hose goes all the way to the back of the trailer).  I positioned the Grey tank hose right up against the pump outlet and made sure that there was enough hose to go all the way to the back of the outlet and then I clipped the excess hose.
    3. Filter outlet hose to Pump inlet: I first attached the new hose to the pump inlet and then I pulled the hose up to the filter and, making sure the new hose went all the way to the back of the filter outlet, made a quick cut with the tube cutter.
    4. After pushing all tubing over the inlet/outlets all the way to the back of them, I screwed the metal clamps over the hose inlets/outlets so they are really tight.
12. After completing the project, I tested the system to make sure the water flowed properly (e.g. shower water drains quickly) and there were no leaks. Click here to see a video of the new system working.

I also installed a new metal Chip Guard from Scamp ($23.63 from Scamp + $20 shipping at the time of the writing), which hangs down to deflect rocks, etc. from hitting the underside of the Scamp.  Our Scamp’s original chip guard was badly dented while off-roading south of the Trona Pinnacles.  I tried to bend it back, but it would have taken a lot of effort, so I decided just to replace it.  With the Scamp’s shower pump now relocated to a protected recessed position and new chip guard, I feel the main parts under the trailer are now very well guarded.   To happier and safer trails ahead!

Disclaimer:  You will get the same great Amazon price by clicking on the links here compared to buying directly on Amazon, but by buying here you will also be supporting the continuation of this website as we get a small commission from each sale.  These are products and procedures we use for our own Scamp that we selected and developed from our own research and experiences.  However, we do not endorse any specific product and cannot guarantee that the products we use are exemplary and the procedures we use are complete, accurate, detail the correct recommended procedures, or apply to your model small travel trailer.  It’s always best to double check with your manufacturer or operation manuals to ensure you are doing everything correctly.